Article

How to configure Wi-Fi TP-LINK. But in some cases the following problems may arise:

How to connect and configure TP-LINK router?

If you want to create a wireless network urgently, you should try to distribute Wi-Fi from your phone or computer, but this option is only suitable as a temporary measure. the user sooner or later will have to get a full router. One of the best manufacturers of wireless routers and related equipment. TP-LINK; will correctly stop the choice on it. How to connect and configure a TP LINK router. try to figure it out.

Immediately after purchasing the TP-LINK router, connect Wi-Fi on a laptop or mobile device will not work; The user will have to go through several steps settings.

The first thing to do is to open the box and carefully inspect the device: it is one, two or three antennas, it is clear, serve for high-quality distribution of Wi-Fi, but with connectors on the back wall you will have to figure it out. The order of their location and the number of nests on different models of routers from the TP-Link may differ; but the form and color remain unchanged.

Checking with the following pattern, the user will easily detect on its device:

  • connector for connecting the power supply (digit 1);
  • Contact for connecting a network cable (LAN, digit 2);
  • Contact block for distribution of wired Internet from Device (WAN, Number 3).

configure, wi-fi, tp-link, some, cases, problems

Before you go to the router settings and set the parameters for yourself, you should connect the power supply unit and the operator to the apartment in the apartment; In addition, during the preparatory work, you will need to connect to a WAN router and a laptop or a computer. for this, a short cable is attached to the manufacturer, which on PC is inserted into the same connector where there used to be LAN.

Fortunately, you can configure modern routers from TP-Link without a disk without installing special programs and drivers. By connecting the device described above, the owner gets the opportunity to immediately proceed to the option of parameters; how to do it, will be told further.

Wi-Fi network without access to the Internet. What to do?

If the problem already happened that the device was connected to the Wi-Fi network, but the sites do not open, then first of all we need to find something. On the Internet, in the router, or in a laptop, tablet and telephone.

Check the operation of the Internet connection without a router

Let’s in order. First, check whether the Internet works, and then you never know. To do this, simply connect a network cable directly to the computer, without a router. If the Internet works fine, then everything is fine, go further. If not, then solve this problem with the provider.

If everything is fine with the Internet, then the problem is, or with a router, or with a laptop, or another device that you want to connect to your Wi-Fi network.

Find out the problem in the router, or in a laptop.

To do this, it is enough to try to connect to your router not only one laptop, but also the phone, tablet, or other laptop. If all devices find your Wi-Fi network, but when connected it will be without access to the Internet (such a connection status can be seen on a laptop). Or simply will not open sites, it means the problem in setting up Wi-Fi router.

Well, if for example, the Internet does not work on the Wi-Fi on one laptop, and the rest of the devices are connected, and open sites, it means the problem in a laptop (not necessarily a laptop, it can be a regular computer with a Wi-Fi receiver).

I hope you managed to find out what the problem is in the router, or in a laptop. And now we will look at how to decide, or at least try to solve, one or another.

Start setting the router from the tablet

By default, Wi-Fi protection is not installed, and your network is open. Now we will connect the tablet to it (this is in my case, when I continue to write the tablet, I will have to have an introduction the device from which we carry out the setting).

We go to the settings of network connections (we need to enable Wi-Fi).

Next, we turn on the Wi-Fi network and on the right in the list are looking for our network.

Here, attention! It will have a standard name and will be open. It is important to choose exactly our network. If you doubt, just turn off your router from the outlet (turn off and turn on the Wi-Fi on the device itself). and see whether the network will disappear. If so, it means that this is your network, choose it.

A window will appear. Just press connecting.

If everything is fine, then the status of “connected” will appear near the network, and the icon with network divisions will appear at the top.

See also  How to configure LG TV. Not all television programs are found

All our tablet is connected to our wireless network. You can proceed to settings.

Customize the router through the browser on the tablet

We need to run any browser. He is exactly on your device. It can be Google Chrome, or some other, standard.

In the browser, press your finger to the address bar and enter the IP address of our rooter. Usually, it is 192.168.one.1, or 192.168.0.one. You can see this address, and standard login / password, from the bottom of your router. They should be indicated there.

So, we recruit this address in the browser, on the tablet, and click the button Go (open, and T. P.).

A window will appear with a login and password request. We enter the standard, usually this is Admin and Admin, and click Login.

It is interesting: why the Internet does not work on the TV when connected via a network cable (without a router)?

So we got into the settings of our new router. The floor of the case has already done

Set the parameters for connecting to the Internet

First of all, we need to configure the router, to work with your provider. Whatever he can connect to the Internet and distribute it to Wi-Fi. To do this, we need to know the parameters that I betrayed you, your provider. You need to know the technology that it uses (Static IP, Dynamic IP, PPPoE, L2TP). and already depending on the technology required parameters. All this data, you can clarify the provider support. At the same time, specify whether the provider is binding on the MAC address.

Attention! If the provider is binding to the MAC address, then you need to call the support of your provider, and ask, link the Internet to the MAC address of the router. View the MAC address of the router, you can from below, on the sticker.

This is the most important point. If you are here for a mistake, your devices will be connected to Wi-Fi, but the Internet will not work.

These parameters, you need to set on the Network. WAN tab. Opposite Wan Connection Type choose the necessary technology. And on the basis of a specific technology, set all the necessary parameters: Name, Login, Static IP, or DNS.

Then, when all settings are specified and checked, press the Save button to save the settings.

Pay special attention to the settings that I wrote above. As I said, they are the most important.

Next, go to the Wireless tab.

Opposite the Wireless Network Name item, we specify the name of your Wi-Fi network (write only by English letters, you can digits). This name will be displayed on all devices.

Opposite the Region, specify the country where you live.

Click the SAVE button to save all changes.

If the window appears, just click OK.

Install protection for wireless network

Open Wireless. Wireless Security.

Select WPA / WPA2. Personal (Recommended).

Opposite PSK Password item come up and write down the password. It will be used to connect to your Wi-Fi. Use English letters and numbers. Make a password minimum in 8 characters. Follow the case of letters, it matters.

Be sure to write down the password on a piece of paper and put it in a safe place to not forget. And then you have to discharge all the settings and configure again.

Do not forget to save the settings by clicking on the SAVE button.

How to set up the Internet on a Wi-Fi router

Connecting a Wi-Fi router to the Internet is made in accordance with the settings of your provider. The provider facilitates the task of the subscriber if it turns into an apartment or house, an Ethernet cable with a configured Internet connection. In this case, the action on the side of the user is minimal. All you need is to connect the cable to Wi-Fi Router.

If there is an ADSL connection on a telephone line, you may need an independent setting. It usually produces technical support provider by hotline phones. Connection parameters can be found on the official website of the company providing Internet access.

Connecting a router to a computer

After purchasing a Wi-Fi router TP-LINK line in the store, buyers become owners of a kit that includes a number of components:

  • Routher housing.
  • Network cable for connecting the device to a computer.
  • Instructions that describe the order to eliminate any faults.
  • Power Supply.
  • Documentation with product specifications.
  • Material CD.

First you need to connect the purchased device to the computer. In frequent cases, the cable that goes in the assortment to the router has a short-length extent. Therefore, the router should be placed near the computer. One side of the cable insert into the connector to connect to the Internet, another to one of several LAN connector connections, which are usually highlighted in yellow and has an appropriate inscription next to them.

Ethernet supplier cable connects to WAN port marked with blue color.

Connect TP-LINK TL-WR841N

You brought a router home, or to the office, it does not matter, open the box and find there many pieces of paper, the disk on which the instruction and the router setup wizard. Also included in the kit, of course, the router itself is, if not, then you were deceived :), a network cable for connecting it to a computer and a power supply, like everything.

It is interesting: Wireless Wi-Fi Internet in the village (village) in a private house. How to organize and what is needed for this?

Connect the router to the computer. Here everything is very simple. We put a router near the computer, just a cable in the kit goes not very long, if necessary, you can scribe more cable (it can even be done yourself, here in more detail). Make this can practically in any computer store.

See also  Login to Android Engineering Menu. Camera settings

We connect to the router power and turn it into a power outlet. Then connect to the blue socket Wan Internet cable. The TP-LINK TL-WR841N router has 4 LAN ports, it means that you can connect 4 computers on a network cable. We connect a computer with a router with a cable that comes in the kit. Here are pictures:

Let’s quickly go through the buttons and connectors:

  • Turn on / off button.
  • Cable electric grid.
  • WAN connector, to connect the Internet.
  • LAN connector for connecting a router to a network cable computer.
  • Enabling QSS.
  • Button to reset the router settings.

That’s all, our router is connected. Let’s now go to the setting.

How to configure TP-LINK router

Overview and configuration of the D-Link DIR-320 modem Setting up Wi-Fi any router TP-LINK is a unified, does not cause any problems. And you can do both quick setup TP-LINK router, and more thorough, manually.

Automatic setting

In order to understand how to quickly configure the TP-LINK router, you should switch over the IP address indicated on the device below. Usually it is 192.168.0.one. Fields for login and password. Username According to the Admin standard, the password is the same. Admin. Then go to the “Fast Setup” tab. After that click “Next”, select the country, provider, connection type.

It is also recommended to put a check mark opposite the inscription “I did not find suitable settings”. Connection Type Select when setting up. In this case, is Dynamic IP, or “Dynamic IP Address”.

Internet connection manually

difficult to do everything manually. IP address, gateway, subnet mask and other accurate settings for the TP-LINK modem, providing its correct operation, should be found out from the provider, select the desired connection type and then fill out all fields to access the Internet.

“House.RU”

For example, consider how the TP-Link router connects to the network from the provider called “House.RU”. In the past it was necessary to learn the MAC address, but now this archaic method does not exist. You must open the “Network” section, after that go to the WAN submenu.

In the “Username” and “Password” fields, indicate that login and password, which is indicated in the concluded contract. Set the checkbox “Always Actively”. As a result, after saving, the Internet should work.

Rostelecom

First, open the “Network” section and go to the WAN submenu. Then select the connection type, most often PPPoE, but setting is identical and for other types. Register in the fields for login and password information specified in the contract. Install the checkbox “always actively”.

“Beeline”

Configuring TP-Link for Bilain, go to the Administration page at 192.168.0.1 and further. to the item “Network”. L2TP / RUSSIA L2TP is displayed in the WAN Connection Type field, and, accordingly, login and password issued by the provider are written to the required fields when concluding the contract. You should install a tick opposite the “Automatic Connection”. In general, the settings make it easy to connect to the TP-LINK router, regardless of the provider.

Wireless network

Wireless Network for TP-LINK Configured on the Wireless. Wireless Settings tab. In a special Basing Settings field, a network name invented independently. Going to Wireless Security Adjusts the security of the connection using password and encryption.

Setting in repeater mode, amplifier, adapter or access point

To configure TP-Link in repeater mode (repeater), amplifier, adapter, or access point, go to the Wireless Settings field, where in Operation Mode) in the drop-down list select the desired option.

Modern TP-LINK routers support IPTV. Interactive Television. There is an opportunity to configure and watch IPTV on Wi-Fi on any devices. In the event that there is a special console, it is recommended to highlight the necessary LAN-port for it working as a bridge. All this is done in the tab “Network”, where you need to go to IPTV.

Individual user connection settings

Options for making additional users with individual settings via web inerta equipment for TP-LINK models.

Dynamic DNS

To enable dynamic DNS in TP-LINK, you must go to the DDNS tab. In the presence of registration on the resources presented in the drop-down menu, enter the login, password and domain, install the checkbox “Enable DDNS” and click “Next”. If the transition is not possible, click on the hyperlink and register.

Security Settings

To protect the data, you should change the password installed by the manufacturer. To do this, find the Password field and enter a new password. In the “Protection” tab, subsection “Configuring basic protection” Install the check mark for switching on SPI firewall. You can set specific computers from which the inteeis is locally managed. To do this, in the “Protection” tab, go to the Local Management submenu, where to register the MAC addresses of computers, which allow access to the inteeis setting with administrator rights.

To exclude the possibility of remote access, go to subparagraph “Remote Control” and install it IP Address: 0.0.0.0. Any other IP address is a potential vulnerability, for example, speaking in the field 255.255.255.255, remote access opens for any other computer.

It is necessary to update the software on a regular basis, because the manufacturer’s company regularly releases “patchwork”, protecting from hacking device by intruders.

Parental control

The corresponding tab is selected on the router page. You should install a check mark opposite the inscription “Include Parental Control”. After this, enter the MAC address of the main computer in a special field. Copy the PC address on which the setting is made, easy: by pressing one button.

See also  How to download music on android. Loading music with VK

The MAC addresses of all controlled computers fit below. Customizable timetable: day, time of action. Formed “White” list of sites for unhindered visits.

Change buttons function

Standard Mechanism Override Buttons in Inteese TP-LINK Model Settings.

Torrent customer setup

On the TP-Link TL 841n intees page there are no standard ways to configure torrent clients. However, a third-party DD-WRT firmware is established, which turns almost any router that has a USB port in torrent client. And possibly without using computer resources, download torrent files to a USB device connected to the router.

Pre-configure connection in Windows

When the TP-LINK Wi-Fi Router is ready to make changes to the connection settings in the operating system network menu.

It is necessary to do this in such a sequence:

  • Through the start button, go to the control panel.
  • Move to the network control center and log in to change the adapter data.
  • Find an active network, display the menu by clicking the right mouse button and select the properties subparagraph.
  • In the window that appears, click on the inscription “Network” and move to Internet versions protocols.
  • Activate commands to automatically get IP and DNS server addresses.
  • Move into the Alternative Configurations tab and set automatic setup mode.
  • Confirm changes by pressing the “OK” sticker.

After the work of the required settings, you need to access the inteees of the router, acting in this order:

  • Start the Internet browser and wait for the page download.
  • Register in the address stitch “192.168.0.1 “or” TplinkLogin.NET ».
  • Enter the data in the Login and Password section installed by default. Most often it is a combination “admin”.

On a note. If the specified combinations are not suitable, you can view the identity of the device on the label, which is glued to the bottom of the case.

Configure TP-Link router on a new firmware version

Let’s proceed to the most important. setting up the TP-LINK router. Instructions are given for the new version of the firmware with white and blue inteeis.

Binding on the MAC address

Some operators require binding to the MAC address (special unique number of any device) to secure the user specific devices to enter the Internet. On gadgets that are not included in the list, the network signal will not be applied. In the quality of such devices, there may be PC (if the connection is wired), the router, TV and T. D.

Find out in support of your operator, whether you need a binding, and if yes, configure it on TP-LINK:

  • Click on the third tab at the top “Advanced Settings”.
  • In the “Security” block, expand the item for MAC addresses.

Activate the binding using the switch at the top

Enter the address of the device you want to bind to the provider’s network

Dynamic or static IP address

If you have a dynamic connection, you do not need to configure the connection. Just make sure that in the “Network” tab, the “Internet” section is the value “Dynamic IP”.

If you have a dynamic address of IP, you don’t need to configure anything in the shell

If your network works on a static IP address, do the following:

    In the drop-down menu, select Static.

Tell all the data that provided you operator

Turn on, if necessary, cloning MAC address

PPPoE connection

PPPOE protocol requires specific data for authorization on the Internet. They are individual for each subscriber. are intended to protect against unauthorized use of the network of user. This protocol support DOM.RU, Rostelecom, TTK and other providers. Let us turn to the setting:

    On the drop-down panel, click PPPoE.

Install PPPoE as a connection type

Expand the “Advanced Settings” menu and select Static or Dynamic IP

Be sure to save all changes after setting

L2TP and PPTP connection (VPN)

Types of L2TP and PPTP compounds belong to private VPN networks. The first protocol is used, for example, the Beeline operator. They have the same setting:

    In the menu with the connection type list, select L2TP or PPTP. depends on which species uses your provider.

Specify the L2TP as a connection type if you have “Beeline”

Wi-Fi Setup

The main thing is to change. password for access point. Need to get into your “wi-fi” was not so easy. Even if you don’t feel sorry for speed and traffic, put the key anyway, because via Wi-Fi network, intruders can access files on your PC. Go to the setting:

    Expand the fourth menu “Wireless Mode”. In the first block with the settings, change, if necessary, the name of your Wi-Fi access point (SSID field).

In “Wireless”, change the name Wi-Fi as desired

Write a password to act for your access point

DHCP Server

The router forms a local network around them, which includes all devices connected to the access point. The DHCP server on the router gives each new gadget’s unique IP address. it is valid only in local, and not in the global network (Internet).

  • In the “Network” menu on the left open the tab of the same name. Put a tick next to “Enable Server”.
  • Determine the address pool (range) for the local router network (repel from the number of gadgets that you will connect to the point). Can be put more than required.

Put the range of IP addresses you need (pool)

Similar Posts

| Denial of responsibility | Contacts |RSS